Surface Scanning Laser Confocal Displacement Meters

LT-9000 series

This model has been discontinued.
Compliance with the certification standard is ensured as of the time of shipment from our company.

Recommended Replaceable Products: Ultra High-Speed/High-Accuracy Laser Displacement Sensor - LK-G5000 series

Controller, Not Subject to Export Control, without Camera Function LT-9001H

LT-9001H - Controller, Not Subject to Export Control, without Camera Function

*Please note that accessories depicted in the image are for illustrative purposes only and may not be included with the product.

Data Sheet (PDF)

Specifications

Model			LT-9001H
Measuring unit compatibility			Measuring units are interchangeable without factory recalibration.
Display	Minimumdisplayable unit		0.1 µm^*1, 1 µm², 0.01 °
	Display range		±9,999.99 µm, ±999,999 µm², 9,999.99 °
	Microscope function		―
	Display cycle		10 times/sec.^*2
Terminal block	Analogue output		±10 V x 2 outputs, output impedance: 100 Ω
	Timing input		Non-voltage input
	Reset input
	Auto-zero input
	Monitor dedicated power supply		24 VDC^*3
Control I/O	Judgment mode	3-step limits output	For OUT1 and OUT2, and NPN open collector output^*4
	Binary mode	Binary output	Measured data output (21 bits), OUT1/OUT2/PROFILE selectable NPN open collector output^*4
		Strobe output	NPN open collector output^*4
		Binary selector output
		Binary selection input	Non-voltage input^*4
	Stability output		NPN open collector output
	Laser remote input		Non-voltage input
	Program switching input		Non-voltage input x 3 inputs
RS-232C interface			Measured data output and control I/O (Selectable up to baud rate 115200 bps.)
Video output			NTSC compliant (PIN connector)
Main functions	Displacement mode		Distance measurement, Transparent objectthickness measurement, Angle measurement,Relative angle measurement, Surface selection,Dark-out, Mask, Trend graph display, and Scanwidth/interval change^*5
	Profile mode		Area selection (Average, Maximum, Minimum, Maximum-to-minimum, Area) Area calculation, Scan width/interval change, Dark-out, Smoothing, Averaging, and Profile data output^*6
	Common		Light intensity accumulation, Microscope (LT-9501H, LT-9501HSO (5654) only), Tolerance judgement, 8-program registration, Calibration, Averaging, Hold modes, Auto-zero, and interface language selection
Rating	Power voltage		100 to 240 VAC ±10 %, 50/60 Hz
	Power consumption		110VA or less
Environmental resistance	Pollution degree		2
	Overvoltage category		II
	Ambient temperature		0 to +35 °C
	Relative humidity		35 to 85 % RH (No condensation)
Weight			Approx. 2.4 kg
^1 Display changes every ±0.3 µm. ^2 Varies depending on the setting ^3 Dedicated power supply for the monitor specified by KEYENCE. ^4 Select either the Limits mode or the Binary mode. ^5 Select either the Distance mode or the Profile mode. （Only distance mode is available with the LT-9501HSO (5654) and LT-9001HSO (5655).）The rating of the NPN open-collector output is 30 mA (30 V or lower) maximum, and residual voltage is 0.5 V.The rating of the Non-voltage input is ON voltage 1 V or lower, and OFF current 0.6 mA or lower. ^6 Select either the Distance mode or the Profile mode. （Only distance mode is available with the LT-9501HSO (5654) and LT-9001HSO (5655).） The rating of the NPN open-collector output is 30 mA (30 V or lower) maximum, and residual voltage is 0.5 V. The rating of the Non-voltage input is ON voltage 1 V or lower, and OFF current 0.6 mA or lower.

Data Sheet (PDF) Other Models